| Product Description Geeetech 3D touch bed leveling sensor for 3D printer
3DTouch is an auto leveling sensor for 3D Printersthat can precisely measure the tilt of your print surface. It can greatly improve theprinting precisionof your 3D Printer.
3DTouchfeatures simple, smartand precise. It could work with nearly any kind of bed materials, such as glasses, woods, metalsand so on.
The main functions and controls of 3DTouch are the same as most auto bed leveling sensors, which consists of a RC servo and a micro switch, thus, 3DTouch can be usedon almost every 3D printer control board.
By using progressively designed solenoid and hall sensor, 3DTouchcanintegratehigh precision in such a simple structure. To make it moreuser-friendly and to bring you more enjoyable printing experience we add many smart functionssuch as self-test, false alarm, alarm releaseandtest mode for M119.
Features:
1.Simple
3DTouch can be easily applied, since it has a small and simple structure.Gathering information & firmware setting will be an easy task, because 3DTouch works as usual auto bed leveling sensor.
2. Smart
Self-test: The push pin is operated two times to test when the power is on
Alarm: The LED light blinks if a problem found on a self-test or on an operation
3. High-precision
3DTouchs Standard Deviation in repeatability is around 0.05mm, at that precise.
If you choose 3DTouch, your 3D printer will be high-class masterpiece, giving you an enjoyable experience.
4.Innovative Solenoid: Ultra Power Saving
On idle state, while the push-pin is whether pulled out or retracted, there are not any electric current flowing on solenoid, and standby electric current in the whole device is below 15mA on average, whereas on working state, while the pin is moving in sudden about 100ms, under 300mA flows in the device.
Low power consumption even further drops joule heating, preventing from heat problem.
5. Technologies
3DTouch consists of Atmel ATtiny13A, solenoid, and a push pin.
6. Wide Selection of Bed
3DTouch does not uses either optical, nor proximity (inductive/capacitive) sensor.
3DTouch is controlled by Hall Effect, providing high precision. Thus the bed material can be selected freely.
7. Optimized structure: Larger Build Size
3DTouch is a small and technology-intensive one. Build size can be set larger than other existing auto bed leveling sensor.
3DTouch uses existing RC Servo motor signal intactly, so just plug 3DTouch on the same pins after removing servo motor.
Specifications:
Voltage: 5V
Current: 15mA
Max. Current: 300mA
Cable length: 150mm
Net Weight: 10g
Shipping weight: 25g
Wiring
3-pin: Brown (-, GND), Red (+5V), Orange (control signal)
2-pin: Black (-, GND), White (Z min)
Package list
1 X 3DTouch Auto leveling sensor
1 X 3Pin Straight Pin
1 X 2Pin Straight Pin
2 X Screw & Nut & Washer
2 X Dupont Housing Shell 3Pin
2 X Dupont Housing Shell 2Pin
3 X Dupont Housing Shell 1Pin
14 X Dupont Terminal
1 X 10K 1/8W Resistor
Operate condition
3DTouch can be operated in the following condition.
One I/O for control (PWM or Software PWM)
One I/O for Zmin(Z Probe)
GND and +5V power
Caution
Additional power supply willbe needed in case your board does not supply enough amperage.
Electronic devices can be damaged or even destroyed if connected to wrongpolarity.[wrong terminal connect to 5V(+) and GND(-)]
Pulling/pushinghard onthe push-pin can damage3DTouch and make it less accurate.
Fix push-pin with locking paint after reassembling or adjusting core.
Do not remove or deform elastic material attached on the push-pin.
Please note that
3D touch auto leveling sensor is not plug_and_play; you will need to do some modification to your firmware and for some control board, you may need to do some soldering work to the connector.What's more, this sensor is not compatible with some boards, such as Melzi V2.0, V3.0 and some MKS board. Please note the wire connection and study if your control board supports 3D touch before order.We have prepared the pins for you.
For detailed instructions, please refer to the user manual from this link
http://www.geeetech.com/wiki/index.php/3DTouch_Auto_Leveling_Sensor
If you need any help, please feel free to contact us.
window.adminAccountId=221834407;
. Brand Name:GEEETECHItem Type:Motor CableModel Number:3D Auto Leveling3D Auto Leveling:3D touch |
