| Product Description TMC2208 TMC2130 ST820 A4988 Drv8825 Stepper Motor Driver StepStick Reprap RAMPS 1.4 MKS GEN L V1.4 SKR V1.4 3D Printer Parts
TMC2209 Link:https://www.aliexpress.com/item/4000382753452.html
TMC2130 V3.0 Introduction:
TMC2130 is a high-performance two-phase stepper motor driver chip with a standard SPI interface and a simple step/dir interface. Very low noise, high load driverdoes not lose step.
Details about the TMC2130 V3.0 driver can be viewed at this link
https://github.com/bigtreetech/BIGTREETECH-TMC2130-V3.0
Details about the TMC2208 V3.0 driver can beviewedat this link
https://github.com/bigtreetech/BIGTREETECH-TMC2208-V3.0
SPI mode firmware change description:
https://www.dropbox.com/s/xwongsgvshapqaj/TMC2130-V2.0%20spi%20firmware.docx?dl=0
About Drv8825
Introduction:
The DRV8825 stepper motor driver carrier is a breakout board for TIs DRV8825 microstepping bipolar stepper motor driver.
The module has a pinout and interface that are nearly identical to those of our A4988 stepper motor driver carriers, so it can be used as a higher-performance drop-in replacement for those boards in many applications.
The DRV8825 features adjustable current limiting, overcurrent and overtemperature protection, and six microstep resolutions (down to 1/32-step). It operates from 8.2 45 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow (rated for up to 2.2 A per coil with sufficient additional cooling).
Features:
Simple step and direction control interface
Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step
Can interface directly with 3.3 V and 5 V systems
Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout
Short-to-ground and shorted-load protection
4-layer, 2 oz copper PCB for improved heat dissipation
Exposed solderable ground pad below the driver IC on the bottom of the PCB
Module size, pinout, and interface match those of our A4988 stepper motor driver carriers in most respects (see the bottom of this page for more information)
Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motors rated voltage to achieve higher step rates
Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay)
45 V maximum supply voltage
Built-in regulator (no external logic voltage supply needed)
Subdivision:
About A4988
Introduction:
This product is a breakout board for Allegros A4988 DMOS Microstepping Driver with Translator and Overcurrent Protection; please read the A4988 datasheet carefully before using this product. This stepper motor driver lets you to operate bipolar stepper motors in full-, half-, quarter-, eighth-, and sixteenth-step modes, with an output drive capacity of up to 35 V and 2 A.
The translator is the key to the easy implementation of the A4988. Simply inputting one pulse on the STEP input drives the motor one microstep. There are no phase sequence tables, high frequency control lines, or complex interfaces to program.The A4988 interface is an ideal fit for applications where a complex microprocessor is unavailable or is overburdened.
Subdivision:
TMC2130 V3.0
TMC2208 V3.0
LV8729
DRV8825
A4988
Details about the TMC2130 V3.0 driver can be viewed at this link
https://github.com/bigtreetech/BIGTREETECH-TMC2130-V3.0
Details about the TMC2208 V3.0 driver can beviewedat this link
https://github.com/bigtreetech/BIGTREETECH-TMC2208-V3.0
window.adminAccountId=201779767;
. Brand Name:BIQUItem Type:DriverModel Number:A4988/DRV8825 Stepper Motor DriverProduct name:A4988/DRV8825/TMC2130/TMC2208/ST820 Stepper Motor DriverMaterial:4-layer PCBSuit for:MKS GEN V1.4/MKS GEN L/SKR/Ramps 1.4 |
